Mtbdog
Well-Known Member
He's retired, kept him busy and out of trouble.Why did you do that Rick? I pulled the ballast and put in 120V LED replacements. I hope to never have to touch them again.
He's retired, kept him busy and out of trouble.Why did you do that Rick? I pulled the ballast and put in 120V LED replacements. I hope to never have to touch them again.
Why did you do that Rick? I pulled the ballast and put in 120V LED replacements. I hope to never have to touch them again.
It's just like replacing the ballast but without actually replacing the ballast.I googled that but seemed too complicated. Next time one burns out (there are 3 fluorescent lights in the basement) I'll look into it again.
You remove the ballast, then wire nut the bulb connectors into the 120V feed. Most bulb replacements come with a sticker that states ballast is removed, and use only LED replacements.I googled that but seemed too complicated. Next time one burns out (there are 3 fluorescent lights in the basement) I'll look into it again.
@rlb keep an eye on the compressor next year or the year after when you clean the fins on it (assuming you do...if not the Googles can help on how). Have seen dryer lint clog the fins on some compressors to the point that the AC doesn't run as cool or as efficiently since air can not flow over the thousands of clogged fins. Also, I have the same Husky lights and they are pretty handy for sureSpent some time fixing up my 70s pink bathroom. The Mrs had a job change recently, so now we're both getting ready at the same time which means I get to shower in the crappy bathroom. It needed a new faucet (old one was constantly dripping) and there was no exhaust fan.
The faucet job was more of a PITA than I expected, mainly due to the stupid plastic nuts that hold it on. It took me a few trips to home depot to finally get the right tool for the job.
I was going to reuse the old supply lines, but I decided on another last minute trip to HD for new ones, cheap insurance. New faucet installed
Next up was the exhaust fan. I picked up an inline unit since I have access to the wall behind the bathroom (my workshop), so this seemed like the best way to go. To make it all work I moved the dryer vent to a new location (which required moving some electrical) and used the former dryer vent for the bathroom exhaust.
Existing dryer vent, and electrical for AC compressor that is exactly where the new vent needs to go
View attachment 115122
New dryer vent through the siding. No pics with the siding off, but it was easier to work with than I expected. I picked up a siding tool a while back (for some other project I never got to) and I was glad to have it on hand. I didn't put the trim cover on yet, because I want to modify it to point left (away from the AC compressor).
Not too many inbetween pics, here's everything all hooked up. The reroute added 2ft to the dryer line, but it's not a very long run so I don't think it will impact drying that much. The bathroom duct routing is a little goofy. I probably could have mounted the fan box on the wall, but I didn't want it sticking out since the fridge needs that space, so I opted for this. I still need to cut the insulation, didn't feel like needing another shower today. I'll get to it....
View attachment 115123
View attachment 115124
Check out that wallpaper
Dewstop automatic switch FTW
View attachment 115125
And finally, my new favorite tool. Been eyeing this at HD for a while, and picked it up just for shits. Turned out to be super useful for this whole project.
@rlb keep an eye on the compressor next year or the year after when you clean the fins on it (assuming you do...if not the Googles can help on how). Have seen dryer lint clog the fins on some compressors to the point that the AC doesn't run as cool or as efficiently since air can not flow over the thousands of clogged fins. Also, I have the same Husky lights and they are pretty handy for sure
Dewstop automatic switch
Had no idea this was a thing. Buying a 2 or 3 gang box (unless someone has one they want to part with?) and installing one of these ASAP
There’s a company bases in Florida called Coastal Source. Pretty high end stuff and you’ll need a dealer to install it. We sell their speaker systems and everything is quality built.Any recos on landscaping lighting systems? I put in solar lights about 2 years ago and they worked well for awhile but don't last down here. Just pulled them all and chucked in the trash. Trying low voltage led this time
There’s a company bases in Florida called Coastal Source. Pretty high end stuff and you’ll need a dealer to install it. We sell their speaker systems and everything is quality built.
Yeah their stuff is pretty indestructible.I get products for Colorado from the same company , not shit like the box stores sell but quality
https://www.coastalsource.com/
I'm looking for a double end supported paint roller frame for std paint rollers (9"). They don't seem to exist in HD or Lowes.
The std paint roller frames flex and it annoys me
Painting ceilings suck
Damn that’s pretty good I sell those for 10x that pice. If you ever need cable or parts let me know Ill hook you up. I won’t charge you 10x the price ?With all the new wifi stuff, like cameras, lights, switches - especially outside the house, I decided to install an outdoor access point.
Basically a weather hardened version of a wireless router. Decided on Comfast. (yeah, not a great name)
$70
https://smile.amazon.com/gp/product/B07FT3LFD6/
It is powered over the ethernet cable, so i purchased a 40m cable rated for outdoor use $30 -
Simple enough - plug short cable (included) into modem, other end to power injector, then the long cable from power injector to access point mounted high in the garage.
Visit the admin page to change the password, and put the unit into access point mode (it can also be used as a router, or bridge), set the wifi name and pw
Great coverage of the yard for $100. There are some things with the OS that need to be corrected, but just geeky stuff, like auto correct the time.
Recommended if you have spotty coverage from your indoor unit...
It can be mounted on a pole/pipe with included straps, or to a wall, using protruding anchors.
View attachment 116286