OOS MOGA

qclabrat said:
This was my first attempt in the comingle. Kids left both bags open so I poured some out to see if either was stale. Got to say it's the perfect combo as it complements each well. GF have a nice light start but end up dry and pasty. Cheezys are not great in the start but have a much more pleasant finish of cheddar. I've found popping 3 fish, chew once then add a cheezy square is an optimal sequence.
Click to expand...
All in the name of science.
 
Kangdoy said:
I did when we rode CR a few weeks back. I let him gave it a try around the ballfields parking lot. After 10 seconds, I was like 'Ok...that's good enough...' 😛
Click to expand...
1557235696467.png
 
@serviceguy
can you post up or PM me where you got your spindle spacers?
I need 24mmx5mm ones and was only able to find them from Asia. Ordered them anyway but I don't want to wait till July 1st which is the ETA. Currently I'm using a carbon 25.4 headtube spacer to figure out the alignment, but not planning to test it out on the trails in that config. Only thing left as the brakes are ready and just waiting for a relatively not wet day for a maiden voyage. Feeling frustrated as you have been on this build.
 
qclabrat said:
@serviceguy
can you post up or PM me where you got your spindle spacers?
I need 24mmx5mm ones and was only able to find them from Asia. Ordered them anyway but I don't want to wait till July 1st which is the ETA. Currently I'm using a carbon 25.4 headtube spacer to figure out the alignment, but not planning to test it out on the trails in that config. Only thing left as the brakes are ready and just waiting for a relatively not wet day for a maiden voyage. Feeling frustrated as you have been on this build.
Click to expand...
Are hub spacers the same diameter? I might have some.
 
Paul H said:
Are hub spacers the same diameter? I might have some.
Click to expand...
not BB spacers, crank spindle on the drive side. The chain ring rubs on the stay and I need about a 5-6mm spacer
PF BB so can't just push out the outboard bearings. Is there a better option?
 
qclabrat said:
not BB spacers, crank spindle on the drive side. The chain ring rubs on the stay and I need about a 5-6mm spacer
PF BB so can't just push out the outboard bearings. Is there a better option?
Click to expand...
24mm? ill go measure some spacers I have at home
Is this direct mount? or bolts?
smaller chain ring not a option?
 
Mtbdog said:
Anyone up for the Tourne this afternoon around 2:30-3?
Click to expand...
Wish I could, but soccer tonight so want to save the legs, but I am hoping if work doesn't get in the way to do WC tomorrow around 3ish. Starting from the Batcave, but it will be very last minute because work has gotten in the way lately
 
Mathers said:
i may be able closer to 3
I would liek to do a long ride is that possble there
Click to expand...
A good loop is about 7 miles, so to get a ride of any length you probably have to do a couple laps. I'm meeting 2 others there at 3 and at 5 the Cycle Craft crew does a Tuesday night ride, I met @Mr. E Man there!
 
Mtbdog said:
A good loop is about 7 miles, so to get a ride of any length you probably have to do a couple laps. I'm meeting 2 others there at 3 and at 5 the Cycle Craft crew does a Tuesday night ride, I met @Mr. E Man there!
Click to expand...
I can't make it tonight, maybe next week... I'm still house hunting... It's literally taking over my life.
 
Mtbdog said:
A good loop is about 7 miles, so to get a ride of any length you probably have to do a couple laps. I'm meeting 2 others there at 3 and at 5 the Cycle Craft crew does a Tuesday night ride, I met @Mr. E Man there!
Click to expand...
Okay don’t wait for me if I’m going to make it I’ll let you know.
 
qclabrat said:
@serviceguy
can you post up or PM me where you got your spindle spacers?
I need 24mmx5mm ones and was only able to find them from Asia. Ordered them anyway but I don't want to wait till July 1st which is the ETA. Currently I'm using a carbon 25.4 headtube spacer to figure out the alignment, but not planning to test it out on the trails in that config. Only thing left as the brakes are ready and just waiting for a relatively not wet day for a maiden voyage. Feeling frustrated as you have been on this build.
Click to expand...

WorldWideCyckery.com, they’re Wheels Manyfactuting spacers and they come in several thicknesses. They do sell 24mm spacers. I got mine in about 3 working days.
https://www.worldwidecyclery.com/pr...MI_9mun_2J4gIVCI7ICh1cwQTCEAQYAyABEgKF2PD_BwE
 
You must log in or register to reply here.
Back
Top Bottom