The DIY thread - DIYourself

It looks like I’ve had a slooooow water leak for years in the pipe in the wall that feeds cold water to my washing machine. Found when I saw a slow drip in the same pipe at the other end that connects to the feeder because that fitting was slow leaking. It looks like someone did piss poor job soldering and it has aged. Plywood is disintegrated and black on the end under the washing machine.

This may turn into a headache restoration job. Is it something home insurance would cover? Calling when they open. Advice on next steps and process?

A
I would at least call insurance company see what they say - after your deductible they may cover at least some of it.
 
It looks like I’ve had a slooooow water leak for years in the pipe in the wall that feeds cold water to my washing machine. Found when I saw a slow drip in the same pipe at the other end that connects to the feeder because that fitting was slow leaking. It looks like someone did piss poor job soldering and it has aged. Plywood is disintegrated and black on the end under the washing machine.

This may turn into a headache restoration job. Is it something home insurance would cover? Calling when they open. Advice on next steps and process?

A
Depends on your deductible. You can always open the claim and then retract if the amount it less than almost your deductible.
 
A neighbor (contractor) is going to come look. No signs of water in the wash room. This is a crawl space.
View attachment 210965

ugly!

looks like the subfloor floor was replaced at some point? the water damage is below the the toe plate of the wall?

Easy peasy - cut the copper back, run some pex to a new washing machine outlet... ignore the water damage.

did you poke it with a screwdriver to see if it is all soft? what about the next joist bay on either side?
 
PXL_20230402_213140618.MP.jpg

Found G-pa's dividers while I was cleaning. The tip was fractured on the one side (they're hardened), and there was a bit of surface rust (luckily not in the bottom drawer of the machinists toolbox...It didn't survive). Bound it together tightly, and re-pointed it, then gave it a thorough polishing/waxed it.

I have two Bailey-type planes that I need to clean/polish, and one jack.
 
Nothing special but after i called the grill manufacturer and asked about replacement parts they sent me a link to an aftermarket part that was $15 EACH (I needed 5 of them )

Went right to Jeffbezos.com and got these for $19.99 plus these are stainless steel and the original ones were that stupid coated porcelain crap. They disintegrated after 1.5 years.

9E6049AB-DC60-427D-984D-FAB3289F55CF.jpegF79EC97C-83EC-4EF2-952D-7539BC2EBBB1.jpegC3614162-2682-4F26-A93C-7508762831C1.jpeg
 
Had a guy come in asking about how to make the profile on the ends of this pergola. A jigsaw would be obvious but seems kind of wide for a jigsaw blade. You would likely have to sand it. If you were going to sand it just use a recip saw then finish it off with a belt. I tend to think a dozen ways to do things but dont have a professional opinion.

Waterproof-Low-Maintenance-Weather-Resistant-Landscaping-Composite-Wood-Garden-WPC-Pergola.jpg
 
Last edited:
Had a guy come in asking about how to make the profile on the ends of this pergola. A jigsaw would be obvious but seems kind of wide for a jigsaw blade. You would likely have to sand it. If you were going to sand it just use a recip saw then finish it off with a belt. I tend to think a dozen ways to do things but dont have a professional opinion.

Waterproof-Low-Maintenance-Weather-Resistant-Landscaping-Composite-Wood-Garden-WPC-Pergola.jpg
I used a jig saw with 5/4 deck planks. Looks fine and less weight helps the overall structure imo
 
Had a guy come in asking about how to make the profile on the ends of this pergola. A jigsaw would be obvious but seems kind of wide for a jigsaw blade. You would likely have to sand it. If you were going to sand it just use a recip saw then finish it off with a belt. I tend to think a dozen ways to do things but dont have a professional opinion.

Waterproof-Low-Maintenance-Weather-Resistant-Landscaping-Composite-Wood-Garden-WPC-Pergola.jpg

rough cut with jigsaw then finish with router with a straight bit and a repeatable pattern. Use a guide bushing or top bearing bit.
Can't do a hard inside corner with it tho
 
Question for the group. Could this be water percolating up from under the slab?

My house is on a slab with French drain. When it rains like this I typically hear the sump pump doing it’s job very well and I always check on it.

This morning before I left for my ride event I had a moment of panic when I saw water on the floor. I was nearly sure my ride day was over before it started and I moved all the stuff out of the way and noticed a puddle of water only about 24” in diameter centered on this spot of the floor.

I checked the furnace and the hot water tank, and the built in humidistat water and drain lines and nothing was wet anywhere near this spot. Hot water tank has a 3”
spill pan under it and a drain into the French drain even if it did leak.

When I got home this afternoon the towels I left there were obviously still wet. I put a new dry one down to see if it happens again.

Never had any issues like this before we’ve had much more rain then the last 24 hours.

Thoughts welcome and I wouldn’t even know who to call to come look at it ? Mason? Foundation guy ?

Totally baffled.

62FB913E-241E-45D7-9AFC-90B3A125226C.jpeg718155AB-F073-430B-A403-E337470FBCA6.jpeg
 
Question for the group. Could this be water percolating up from under the slab?

My house is on a slab with French drain. When it rains like this I typically hear the sump pump doing it’s job very well and I always check on it.

This morning before I left for my ride event I had a moment of panic when I saw water on the floor. I was nearly sure my ride day was over before it started and I moved all the stuff out of the way and noticed a puddle of water only about 24” in diameter centered on this spot of the floor.

I checked the furnace and the hot water tank, and the built in humidistat water and drain lines and nothing was wet anywhere near this spot. Hot water tank has a 3”
spill pan under it and a drain into the French drain even if it did leak.

When I got home this afternoon the towels I left there were obviously still wet. I put a new dry one down to see if it happens again.

Never had any issues like this before we’ve had much more rain then the last 24 hours.

Thoughts welcome and I wouldn’t even know who to call to come look at it ? Mason? Foundation guy ?

Totally baffled.

View attachment 212552View attachment 212553

yes. it pushed up through the slab.
 
Any chance your gutters are overflowing? Clogged pipes that take water away from the house?

I have interior and exterior perimeter drains and still get water pushing up during extended rain events.
Will have to check that especially the one on the deck closest to that side of the house.
 
Any chance your gutters are overflowing? Clogged pipes that take water away from the house?

I have interior and exterior perimeter drains and still get water pushing up during extended rain events.
Is there any chance that is some cases a hole is left intentionally in the slab to let water get pass the slab and into the basement? I guess to prevent the slab from cracking? When I lived in Clifton we got the basement flooded during Sandy, turned out all the water came through this single hole in the middle of the slab that kept pouring, supposedly from drawing water from the raised water table underneath…
 
Is there any chance that is some cases a hole is left intentionally in the slab to let water get pass the slab and into the basement? I guess to prevent the slab from cracking? When I lived in Clifton we got the basement flooded during Sandy, turned out all the water came through this single hole in the middle of the slab that kept pouring, supposedly from drawing water from the raised water table underneath…

perhaps it was meant to be a drain?

maybe someone stuck a log in it, to walk on when it was muddy? 😉
 
Is there any chance that is some cases a hole is left intentionally in the slab to let water get pass the slab and into the basement? I guess to prevent the slab from cracking? When I lived in Clifton we got the basement flooded during Sandy, turned out all the water came through this single hole in the middle of the slab that kept pouring, supposedly from drawing water from the raised water table underneath…
If you’re referring to my picture above I have Been living here since 2001 never had this happen
 
Back
Top Bottom