Search results

  1. smufguy

    Car A/C repair

    Slow leaks are hard to spot when the engine and the condenser fans are running. My wife's MB C280 had a bad coupler on the condenser itself and it was obvious when I charged it up. Usually once the system is pressurized and you run the car and turn it off, medium to large leaks are very evident...
  2. smufguy

    Computer mount?

    I have only seen very few that adapt to the handlebar clamps. Something like this >>Handle bar extender would not be too bad.
  3. smufguy

    Grease and lube

    I have always used Mobil 1 Syn grease and automotive assembly grease to get headsets and threads set. They are usually not long lasting, so cant be used for prolonged lubrication. Bike assembly lubes are NOT the same as automotive assembly lubes so do not use them for the above. For stanchions...
  4. smufguy

    Cleaning & Lubing chain

    I am the same with the Simple green. Dilute it with hot tap water, soak it for 15 minutes, brush the chain and rinse it in the same Simple Green solution to get out the dirt. Then rinse it again in hot tap water rag dry it and let it dry out by my water boiler exhaust or by my furnace exhaust...
  5. smufguy

    Halter's Cycles

    Good and Bad news. Bad news: You are much further away from my house Good news: You are down the street from my most favorite town....... Princeton!! Either way, its good news that you guys found a new place. Best of Luck for you Jason.
  6. smufguy

    Efinger Sporting

    He surely does. Every store has its following and I enjoy two stores, and Efinger is one of them. Marc is a genuinely a wonderful guy.
  7. smufguy

    Efinger Sporting

    Stopped by Efinger Sporting Goods in Bound Brook yesterday to get GU energy gels. Around 3pm, the store was packed and the store was completely redone, especially in the Camping and biking departments. I came back after work and was bought a box of GU (24 pacs in a box) and Mark came running to...
  8. smufguy

    What have you done to your bike today?

    Had to change the headset bearings on the Enduro couple of weeks ago. The old one, that came from the shop, was rusted on the bottom and the top had bearings and the plastic holder broken and about 3 bearings and its holder ring were missing. Mystery. Found out the integrated bearings are...
  9. smufguy

    Bikers & Hikers

    I was at Lewis Morris this past Saturday with 12 other riders, we started early and met maybe 4 other riders on the trail. Two of them, gave no concern for climbers and they were descending. On on of the climbs, I jumped off the bike and tucked myself away from the path as the moron was just...
  10. smufguy

    ear wind noise

    I second this. In winter, when I ride the roads, I use my fleece cap and throw in my Ironman headphones with the mp3 players set to volume 2 (max is 30). I can still hear the cars, and voice, but the wind noise is next to non-existent.
  11. smufguy

    Yes a Shimano or SRAM question but need experienced feedback please .

    I have used SRAM Front derailleur, cassette, chain on one bike and Shimano XT on two bikes. The shifers were XT and also Sram X9. Right now my bike it setup with a 9speed Shimano Ultegra Chain, Saint cassette, X0 RD, XT FD, Shimano XT Cranks and X9 shifters. My shifts have been better with...
  12. smufguy

    Suspension Not Extending Fully

    Eric, if Tim's suggestion does not work, then do the following. The issues with the used bikes/fork is that the usage and ride pattern is pretty much impossible to know truthfully. I ride with guys who get them off ebay and eventhough they are Fox, some dont travel at full or even have the...
  13. smufguy

    need a front tire

    I run Specialized Eskar Armadillo Elite tires in the rear of my bike and the front runs on the stock S-works Eskar. As much as I love the S-Works, the Armadillo Elite is one tough bastard. It is a bitch and a half to put on and once sealed, it is not going anywhere. I have run my bike at...
  14. smufguy

    brake diagnosis

    Cuda, this is what you do. Take the rear wheel off and the pads off the caliper. Clean the pads with degreaser, wash and then completely clean with alcohol. Then take a heavy grit sand paper and sad few layers off the pads and set the pads aside. Now your attention to the rear wheel/disk...
  15. smufguy

    Need more front brake

    Your center of mass and your weight plays a role in selecting the rotor size. Even though a larger diameter brake disk (for a given brake pad contact) provides higher brake torque resulting in quicker/shorter stops. Swap the rotor size to either a 185 or 203mm with proper caliper adapter and try...
  16. smufguy

    Trail Video

    Its up the street from Round Valley, not bad. Would 15 Nassau Rd, High Bridge, NJ 08829 be the closest address or 2 Nassau Rd ?
  17. smufguy

    What have you done to your bike today?

    Replaced the major drive line components including the Chain (Shimano HG93), the Cassette (9speed Saint HG80) and the rear brake pad with the EBC Red. Cleaned and repacked the rear derailleur wheels and front axle. Had the shop tune the front derailleur and readjust the headset because of a...
  18. smufguy

    What have you done to your bike today?

    1speed, the bottom of your crankarms look like they were molested by a crackhead. That is brutal my man.
  19. smufguy

    Bash guard

    Yes sir, have been riding the tooth fair trip ring for the last 4 years. I had them initially on my FSRxc and now its new home is my Enduro. Recommended by Gary from Bike N Gear. Solid one, but if you want to run all three crank gears, you need longer bolts and additional washers. I had Efingers...
  20. smufguy

    Creaky seat post!

    For assembling parts, but not lubricate them, I have had good luck with automotive assembly grease. They are very light, wont add weight or depth.
Top Bottom